Blacktop Patching and Sealing Tips
Blacktop Patching - The homeowner repaired a sinking hole in this blacktop drive using epoxy and stones. It’s time to cut it out and install real hot mix asphalt. Copyright 2023 Tim Carter ALL RIGHTS RESERVED
Blacktop Patching and Sealing Tips - Patch Then Wait 90 Days
Who’s not seen asphalt paving? I have to believe you’ve walked across it on your own driveway, crossed public streets, and/or traipsed across parking lots paved with this magic mix of liquid asphalt cement, sand, and small stone chips. The professionals call it asphaltic concrete. It’s an accurate description because regular concrete has stones, sand, Portland cement, and water to activate the cement.
Tar and Chip - The Original Blacktop
Did you know that before hot mix asphalt was invented most paved roads in the USA were created using the hot asphalt liquid cement sprayed on top of compacted gravel? Small stone chips were immediately broadcast on the black coating and compacted to create extremely durable road surfaces. In many rural areas of the USA, this tar-and-chip method of paving is still used on thousands of miles of secondary roads.
This tar and chip method of asphalt paving allows you to introduce color to your driveway depending on the color of the stones you broadcast over the liquid asphalt. I had a medium-brown driveway that used chert road metal from the Meramec River region in Missouri. You could have a red, green, or beige driveway depending on what type of durable chip gravel is available where you live. You can read all about tar and chip driveways and watch videos of the process on my www.AsktheBuilder.com website.
Do you have sunken and cracked places in your blacktop driveway? How about edges where a long crescent-shaped piece of asphalt has cracked or broken away? These defects can almost always be traced to an inferior gravel base under the blacktop. Blacktop itself is a flexible pavement because asphalt itself is a semi-solid material somewhat similar to glass. Glass succumbs to gravity over many years and asphalt can creep and deflect when compressed.
This is crumbling blacktop that needs to be removed and patched with hot mix. The 5-gallon bucket is for scale.
If you want an asphalt driveway to last, the soil under it must be strong and the gravel base must be at least six inches thick. Eight or ten inches would be better. You must use crushed gravel that contains a variety of stone sizes including stone dust. The dust helps knit all the stones together serving the same purpose that sand does in regular concrete.
I’ve experimented in the past with the cold asphalt patching materials you can purchase at hardware or big-box retailers. Once exposed to air, the water surrounding the actual asphalt evaporates and the material does get quite hard. That said, it’s not the same as using the real deal, hot-mix asphalt made at an asphalt plant. Hot mix patching done correctly can produce a patch that lasts for decades assuming the gravel base is deep and compacted.
Patching potholes might be on your list of things to do. If so, do it the same way dentists install a filling in a tooth. Excavate the sides of the pothole so it looks like an upside-down ice cream cone. You want the bottom of the pothole to be bigger than the top. This way when the hot mix becomes solid, it can’t pop out of the hole.
If you’re going to patch larger areas in your drive, try to use a pavement saw to make clean-cut edges. Compact the gravel base and install the blacktop at least 1.5 inches thick. Two inches would be better. Be sure to dust off the sides of the saw-cut blacktop to get as good a bond as you can between the old and new.
This is a great example of saw-cutting blacktop to create a nice clean edge. The only thing missing is an asphalt sealant that should be applied over the saw cut much like you tape a drywall seam with mud and paper. Copyright 2023 Tim Carter
The best way to patch potholes and patches up to 4 feet square is to use a contractor who has a special heater that heats up the existing blacktop to the same temperature it comes from the asphalt plant. This way the fresh patching asphalt mix bonds mechanically and chemically with the old asphalt. When done correctly, you can’t even see where the old hole was as there are no saw-cut lines.
Do NOT Seal New Blacktop
Whatever you do, never seal new blacktop or a blacktop patch just after you finish. The asphalt needs to cure for a minimum of 90 to 120 days. The lighter-weight oils in the asphalt need to evaporate allowing the asphalt to get hard. If you seal it before the oils evaporate, the asphalt stays soft for a very long time making it susceptible to damage from motorcycle kickstands, and tires that turn in place.
It's best to wait a few years before sealing new blacktop. If the blacktop is still jet black in appearance, it has plenty of asphalt cement still up at the surface to offer protection. Once the blacktop starts to turn gray where you see the actual color of the stones and sand, then it's time to seal it. Keep in mind the sealers are no more than paint and will wear off again.
Roadways are not sealed because the heavy vehicular traffic would wear off the sealer in a short amount of time.
The jet-black asphalt in the cul-de-sac is just weeks old. The light-gray blacktop driveway used to look identical. But years of exposure have allowed the thin asphalt cement coating to wear off the stones and sand. It's time to seal the light-gray driveway. Copyright 2023 Tim Carter ALL RIGHTS RESERVED
If you’re installing a new blacktop drive, the best thing you can do is install the gravel base at least one foot wider than the final blacktop drive. This gives you a 6-inch-wide gravel border around the new blacktop. This shoulder provides the all-important lateral support.
Without this support, if a heavy truck or concentrated load is placed right at the edge of the driveway, you can expect the asphalt to crack as the weight causes the blacktop and gravel beneath to move sideways towards the soft soil.
Column 1511