Low Water Flow in Luxury Shower

There's water flowing from the large shower head. However, as soon as you turn on the three body sprays water dribbles out of every orifice in this luxury shower. The East Coast plumber was a dunce. Copyright 2024 Tim Carter

Low Water Flow in Luxury Shower - Pipe Size is Too Small

Each week, I extract quite a few homeowners like you from wretched remodeling or home-building quagmires. I do it with a phone or video call. Feel free to set up a phone call with me here. In almost all cases, the root causes of the dilemmas are poor plans, sketchy or non-existent specifications, and misplaced trust.

A week ago, a middle-aged woman was lamenting about her luxury master shower remodel. The walls were covered in breathtaking marble. Step into this private oasis, and you will see a large rain shower head, three body sprays, and a hand shower wand.

What the woman didn’t have was water flow. A somewhat decent flow would come out of the shower head on its own, but if you turned on any of the other accessories while water was flowing from the shower head, the water flow and pressure would drop. It was pathetic and unacceptable. Sadly, she didn’t discover this until after the entire shower was complete. When she entered the shower to enjoy it for the first time, she exited the shower wet and disgruntled.

Low Water Flow - Luxury shower heads, body sprays, and hand showers gulp water faster than thirsty horses. Plumbers who fail to do water-flow calculations might be paying a tile contractor big money to re-install the marble or tile. Copyright 2024 Tim Carter

Low Water Flow Excuses by the Contractor

As you might imagine, she complained to the remodeling contractor. The project superintendent and the plumber immediately said the water pressure in the house was too low. They were sure a booster pump would solve the problem.

Perform a Pressure Test When Bidding

Just like doctors order scans, x-rays, and other tests before performing surgery, the plumber should have performed a pressure test before he cut open the walls. It was his professional obligation to determine if the existing conditions would support the new fixtures that have an insatiable appetite for water. You can purchase an accurate pressure gauge that connects to a hose bib or laundry-tray faucet to see what the pressure is in your home. The luxury showers work best with a pressure of about 70 PSI. Any pressure below 50 PSI will produce less than vigorous water flow. Keep reading how to test to see if you get the desired result.

This gauge cost lest than $10 in 2024. Get one now. CLICK THE PHOTO

Low Water Flow Usually Means Pipes are Too Small

I’ve been a master plumber for over four decades and knew immediately what was causing the low-pressure and volume issues.

Yes, it's me, Tim Carter! I'm taking a break from installing a garage floor drain in my daughter's home on Mt. Desert Island in Downeast Maine. Go HERE NOW if you need to hire me to solve your low water pressure and flow problems.

The woman was smart enough to take photos of the job's progress. Several photos showed the plumber installed 1/2-inch PEX water lines with flow-restricting hard 90-degree fittings. This PEX fed water to all the accessories.

It’s important to realize before the work began the water pressure and flow in the original tub and shower was fine. An independent inspector verified the incoming water pressure was 70 pounds per square inch (PSI). The woman shared that prior to the remodeling, she could take a wonderful shower with plenty of water. Her tub spigot gushed water if she wanted to soak in a bath. The tub and shower were piped with 1/2-inch copper tubing.

If you don’t want to be frustrated with your new fancy shower, please pay attention. All of the pain the woman has endured could have been avoided with a pencil, paper, and ten minutes of time. The plumber failed to do the simple calculations that would have shown him the correct pipe size to feed the bathroom and the size of the pipes that extended to each accessory. Low water pressure can be caused by many things.

You can view the Uniform Plumbing Code online. Within this large document, you’ll discover a table showing load values for all the common fixtures in your home. The load values are stated in water supply fixture units (WSFU). It just so happens that one WSFU equals one gallon of water a minute of flow.

Calculating Water Supply Fixture Units a Must

A normal residential bathroom like the woman had before the remodeler showed up has 2.7 WSFU of cold and 1.5 WSFU of hot water. Since you don’t use all the fixtures at the same time while in the bathroom, the blended total is 3.6 WSFU. A normal shower head has 1.4 WSFU. A seasoned plumber would almost always run a 3/4-inch diameter cold and hot water line to this bathroom. He’d branch off this larger pipe with a 1/2-inch pipe to each fixture. It’s quite possible the woman’s shower, once the calculations were run, might require 1-inch hot and cold water lines to be extended from the basement up to the second-floor bathroom.

All five of the new fixtures in the shower consume 11 gallons of water per minute if you turn them all on at the same time. That’s just about ten times the water flow the original shower head consumed! The gallon-per-minute (GPM) flow of each accessory can be found in seconds in the product brochure or online specification sheet.

It doesn’t end there. A diligent plumber will also calculate the pressure loss from the height of the bathroom above the water meter, the pressure loss through the water meter, a backflow preventer, and any other pressure regulators.

PEX Tubing Has a Smaller Inner Diameter

Here’s another factor the woman’s plumber probably didn’t take into consideration. He replaced the copper tubing with plastic PEX. One-half-inch PEX tubing has a slightly smaller inner diameter than one-half-inch copper. The plumber made the situation worse by using the smaller diameter PEX.

Get on a Bathing Suit

Here’s what you should do when you get ready to install a luxury water sports arena in your home. Include in your contract with the builder or remodeling contractor the plumber must produce all the pipe-sizing calculations. You can easily find webpages that allow you to determine pipe size once you know the total WSFU load in your job.

All that said, don’t hope it’s all going to work. Put it in your contract that you get to test the new shower before the marble or tile is installed. It would take just a few hours for the plumber or remodeling contractor to cover the walls with 6-mil plastic that’s taped to the shower drain. Be sure to put down a rubber mat or two because wet plastic is as slippery as wet ice. Give the new shower a test drive before the expensive tile and marble is installed. You should only hope for things you can’t control, like the weather and lottery numbers.

Column 1548